Essential Plumber Guide for Installing a Bathtub
Essential Plumber Guide for Installing a Bathtub
Blog Article
They are making several great observations about Installing A Bathtub in general in the content followed below.
Installing a tub isn't specifically rocket science, but it does call for solid plumbing, woodworking, and also occasionally, tiling abilities. Changing an old bathtub with a brand-new one is also a moderately tough project. If the old tub is easily available, the task can move speedily; if you have to open a wall surface to eliminate the old bathtub and also place the brand-new tub, the task is a lot harder. In either case, the project is within a home handyman's skills, although you will need an assistant to move out the old bathtub as well as set in the new one. Make certain you have qualified on your own for the work and are comfortable attempting it. Rather than employing a contractor to take control of a halfway-completed project, it is better to consider employing one before you start. Chances are you might require an expert plumber to make tube connections.
This article will certainly assist you install a brand-new bathtub in your restroom if you have actually already bought a brand-new bathtub as well as don't require to alter the setup of your previous water system pipelines.
Your tools and also material list must consist of the following:
Removing Old Touches
If you need to replace old faucets with new ones as a part of your installation, after that the first thing you ought to do is detach the supply of water. After doing so, activate the taps to drain pipes any kind of water staying in the system. The process of eliminating the existing faucets can be quite bothersome as a result of the restricted gain access to that is usually the case.
Make use of a container wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipes to the faucets. Have a cloth all set for the staying water that will certainly come from the pipes. When the supply pipelines have actually been gotten rid of, use the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from turning during this procedure. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any type of old sealing compound.
Prior to carrying on to fit the brand-new taps, compare the pipeline links on the old taps to the new faucets. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.
Suitable New Taps
If the tails of the brand-new taps are plastic, after that you will require a plastic port to prevent damages to the string. One end of the adapter fits on the plastic tail of the faucet and the other end supplies a link to the existing supply pipes.
If you require to fit a monobloc, then you will certainly require reducing couplers, which attaches the 10mm pipeline of the monobloc to the typical 15mm supply pipeline.
Next off, place the tap in the mounting opening in the bath/basin making sure that the washing machines are in location between the faucet and also the sink. Safeguard the tap in place with the producer supplied backnut. When the faucet is firmly in position, the supply pipelines can be attached to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with normal tap adapters. The previous kind must be linked to the tap finishes first, tightening just by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Setting up the Bath tub
Making use of the two wood boards under its feet, put the bathtub in the called for setting. The wood boards are helpful in equally spreading the weight of the tub over the area of the boards as opposed to concentrating all the weight onto 4 tiny factors.
The next objective is to guarantee that the bathtub is leveled all round. This can be achieved by examining the spirit level and also readjusting the feet on the tub up until the level checks out level.
To set up taps, fit the bottom of the outermost adaptable faucet adapter to the suitable supply pipe by making a compression join; then do the exact same for the various other faucet.
Turn on the water and also examine all joints and also brand-new pipework for leaks as well as tighten them if required. Fill the bathtub as well as additionally examine the overflow electrical outlet and the normal electrical outlet for leakages.
Lastly, repair the bathroom paneling as defined in the producer's instruction manual. Tiling as well as sealing around the bath tub ought to wait until the tub has been made use of a minimum of once as this will certainly resolve it right into its final placement.
Getting ready for the Installation
First of all, the sustaining structure provided with the bath must be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to see to it that if the faucet comes with a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bathroom, it is additionally reasonable to fit a supporting plate under the faucets unit to prevent pressure on the bath tub.
Fit the flexible faucet adapters to the bottom of both taps using 2 nuts as well as olives (often supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the electrical outlet with the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make certain you make use of all of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom need to currently prepare to be fitted in its last setting.
Tiling Around the Bath tub
In the location where the bath fulfills the floor tile, it is essential to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to split a rigid seal, creating the water to pass through the wall in between the bathroom and the tiling, resulting in problems with moisture and also possible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to assimilate your fixtures and also installations. They are sold in tubes as well as cartridges, and also are capable of securing spaces up to a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill the tub with water before securing, to permit the motion experienced when the bathtub remains in use. The sealant can split rather early if you do not take into consideration this motion prior to securing.
Alternatively, ceramic coving or quadrant tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally conveniently available on the marketplace. It is advisable to fit the tiles making use of waterproof or water resistant sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
We were made aware of that report on Tools You Need to Install a New Bathtub through an acquaintance on our other web blog. Please take the time to share this blog entry if you appreciated it. We cherish reading our article about How to Install a Bathtub Yourself.
Immediate response? Call. Report this page